How to Remote Control Light Stations

A beacon is a light or fire on the hill or tower which acts as a signal or a warning to help guide navigator to their destination with safety.We also can say "Light Station" One customer said, “I’m looking for a system which can remotely control (200m max) ignition of a light station in 24 V dc”.

We recommend him the model of single channel 24V power output RF remote (S1X-DC24-ANT2 +1CB-2). Single channel is for one device. 24V direct power output can supply power directly to the device which is controlled. User can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. The receiver, which mounts long range magnetic antenna, pairs with long distance transmitter to reach to 2000m in the open field.

There are 3 control modes. They are Toggle, momentary and latched.
Setting control mode Toggle: Only connect Jumper-2.
1) Press big button: Turn on the relay.
Press big button again: Turn off the relay.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold big button: Turn on the relay.
Release big button: Turn off the relay.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay.
Press small button: Turn off the relay.
As regards controlling beacon, we suggest the latched mode. Press big button to turn on beacon light, press small button to turn off the light.
For the wiring, it is so simple. The following picture shows. Lamp is connected to terminals A&B on the receiver. The receiver should be supplied 12V power. There is no need to supply power to lamp because lamp can get power from the receiver.

Waterproof Remote Control for 2 LED Lamps

A brand new 2 channel 12V toggle remote control kit(S2RX-DC12 & C-2) is promoting now. The receiver is installed in a black waterproof case. Six colors‘ wires are connected inside terminals of the receiver. Wires are bound together and stuffed in black connection wire.The connection wire outside of the case is 20 cm. Wireless control 12V electronics including lights, LEDs, relays, dc motors and other low current devices.You can control receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. This video aims to show you how to control 2 led lamps.
Wires:
Red    =  Input +12V
Black  =  Input Ground (-)
Yellow =  Output 1 +12V
Brown  =  Output 1 Ground (-)
Blue   =  Output 2 +12V
Green  =  Output 2 Ground (-)
Operation Video:

2 Channel DC Remote Controller with Manual Button and Limit Switch Function

With high power of 30A. Control DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V /24V.
You can rotate the motor in positive or reversal direction with the transmitter (remote control) from any place within a reliable distance; the wireless signal can pass through walls, floors and doors.

The remarkable characteristic of this controller is that its manual switch and limit switch, which meet your different requirements.

2CH RF DC Remote Control Kit Controls AC Motor

This 2CH RF DC remote control kit is activated by DC power supply, which operates in toggle, momentary, latched and toggle +momentary modes (just set according to your requirement).It is very favorable for lights or other DC/AC electric devices which are hard to reach or far away from switch. This 2 channel remote control kit can help you complete two operations at the same time. It is widely used for lights, gates, garage doors, motors and so on.
We will try to show you how to control positive and reversal rotation of an AC motor with this remote module.

1 CH Latched Remote Controller Controls LED Lamp

It is the 12 V one channel latched mode remote control. It is also activated by 12V power supply. Paired with long distance transmitter CB-2, its working distance can be 1000m (3000ft). There is no need to go up and down the mast to turn device on and off. Using a remote controller to control device, it is very convenient to you. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time. So the big button of this transmitter only turns on the
device when you press. And the small button only turns off the device.
We made a demonstration to show how to use this remote controller.

One Transimtter to Many Receivers— Control 4 Lamps

The receiver is designed for one-transmitter-many-receivers system. There are two channels for each receiver. You can use 2 receivers with transmitter CV-4 or CB-4. You also can choose external antennas for them. With the extended external antennas, the transmitting distance will reach about 2000m in the open air. This kit is also a multi-mode remote control which includes four working modes, toggle, momentary, latched and momentary+toggle.

 

High Power Motor Remote Model

It is designed to control DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V / 24V. The maximum working current is 30amp. So you will be satisfied with it. You can rotate the motor in positive or reversal direction with the transmitter (remote control) from any place within a reliable distance (within 500m/ 1500ft); the wireless signal can pass through walls, floors and doors.