High Power Remote Control for 2 LED Light

S2PX-DC12+C-2
Wireless control, easy to install
With high power of 30A
Direct dc power output; control Lights, Motors, Fans, electrically operated Doors / Locks /
Windows / Blinds / Cars or Other Appliances.
You can turn on/off the receiver with transmitter (remote control) from any place within a
reliable distance; the wireless RF signal can pass through walls, floors and doors.
This video shows to you how to control 2 lamps.

Remote Control RV's Flood Lights

Question from customer:
I want to use this remote kit to operate 4 ea.-12 volt flood lights on my RV (recreational vehicle) from inside my automobile if backing up at nighttime. I would keep one remote in my truck and one in the RV. Will this be a problem that the remote inside my truck will be at a distance of about 50 feet from the receivers inside the RV?

Answer:
We recommend you 4 models of high power dc remote switch with direct power output (S1PX-DC12) and 2 long range transmitters (CB-4). Direct power output; controlling lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. When it pairs with the long range transmitter, the working distance will reach 500m (1600ft) in the open field. There is no need to worry about the distance. The most important point is that encoding of receivers is same as the code of transmitters. So they can work together.


Wiring:
The wiring is very simple. According to the wiring diagram, each light should be connected to corresponding receiver and place to appropriate position. Each receiver is supplied 12V power supply.


Usage:
There are 3 operational modes. Toggle, momentary and latched modes.
Setting control mode Toggle: Only connect Jumper-2.
Press big button: Turn on the relay.
Press big button again: Turn off the relay.
Setting control mode Momentary: Only connect Jumper-1.
Press and hold big button: Turn on the relay.
Release big button: Turn off the relay.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay.
Press small button: Turn off the relay.
You can choose latched mode since you have two transmitters. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time. To be more specific, when you control the light by latched mode, you should prepare at least two buttons remote. Press button A, the light is on; press button B, the light is off.
Button A&B of first transmitter can control the first light. Button C&D of the first transmitter can control the second light.
Button A&B of second transmitter can control the third light. Button C&D of the second transmitter can control the fourth light.

2 Channel DC Remote Controller with Manual Button and Limit Switch Function

With high power of 30A. Control DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V /24V.
You can rotate the motor in positive or reversal direction with the transmitter (remote control) from any place within a reliable distance; the wireless signal can pass through walls, floors and doors.

The remarkable characteristic of this controller is that its manual switch and limit switch, which meet your different requirements.

High Power Motor Remote Model

It is designed to control DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V / 24V. The maximum working current is 30amp. So you will be satisfied with it. You can rotate the motor in positive or reversal direction with the transmitter (remote control) from any place within a reliable distance (within 500m/ 1500ft); the wireless signal can pass through walls, floors and doors.

 

Mixed Modes High Power RF Remote Control Activates DC Motor to Rotate

This is the high power rf remote control which has mixed modes including toggle mode, momentary mode, latched mode as well as momentary+toggle mode.  It can activate dc motor to rotate in positive and reverse direction.

1 Channel High Power Direct Power Output Remote Switch for Irrigation System

Tom is trying to design and build a remote switch system for his sprinkler system. He needs to use the sprinkler controller (12v output for on) to trigger a transmitter to switch a 12v operated valve on the other side of the yard (about 300m away.) He has mains power at both locations but the underground 12v wire from the controller has been damaged so he would like to build a remote system to save putting new conduit for around 300m across the yard.
The easy part would be the receiver end because he would only need a 12v power supply. The hard part will be getting the transmitter to switch on when the sprinkler controller switches on (12v).

We recommend direct power output high power long range remote control kit—S1PX-DC12-ANT2+CB-2V. The remarkable feature of this kit is that its transmitter is triggered DC power 5~28V input. That is to say, the transmitter will send out RF signal to receiver as long as it gets a 5~28V voltage from a device. Besides this advantage, its working distance is up to 2000m (6000ft). And the working current is 30amp. RF signal can pass through doors, walls and other obstacles.

Look at the following simulated diagram. The sprinkler control controls the valve box through the underground electrical wire initially. Unfortunately, the wire has been damaged. However, customer is unwilling to put new conduit for about 300m across the yard.

So using our product to solve this problem is a wise choice. We connect the black wire of transmitter to the common wire of sprinkler controller; Connect the red wire of transmitter to wire from controller to valve. On the other hand, in the control valve box, valve common wire is supposed to be connected to the negative terminal of receiver; valve wire should be connected to the positive terminal of receiver. (As the following application circuit shown)


When you switch on sprinkler controller, the transmitter will be triggered by 12V voltage from sprinkler controller and sent out RF signal to indicate receiver to work. The valve is open and it starts the irrigation. Likewise, you switch off sprinkler controller, the triggered transmitter will indicate receiver to stop working. The valve is closed and it stops the irrigation.
There is no need to put new wire between sprinkler controller and valve control box. It is no longer the hardest part of getting transmitter to switch on when the sprinkler controller switches on.

Telecontrol of 4 Ceiling Lights in Indoor Stadium

The rf wireless distant control technology can be leisurely used to control  lights from outdoor as well. There are 4 big ceiling lights installed on the ceiling of an indoor stadium which managed by a PE teaching headmaster from a primary school. He must go to touch the manual switches one by one when teachers had PE class in the indoor stadium. However, ceiling lights’ switch was installed on a wall outside of stadium gate. It is not convenient to him to go back and forth. So he would like to find effective way to solve this problem.

I think that he need a distant controller to deal with this situation. A 4 channel high power great range ac distant control kit is very favourable for him. It contains 4-channel high power ac output receiver and one great range 4-button remote transmitter. Working distance of this set is 2000m (6000ft) in the open air with external magnetic mount antenna. 4-channel remote control has 4 working modes. They are toggle mode, momentary mode, latched mode and momentary +toggle mode which will satisfy his different needs.

Wiring is fairly simple. Do as the following picture shows. Wire each spotlight to each relay; use transmitter to remote control them. Four buttons control corresponding spotlight respectively.

 

Automatic Controllable Pool Cover by Remote Controller

With the benefits of safety, convenience, water conservation, energy efficiency and easier maintenance, swimming pool covers have increased being used for many families recently. People prefer to use automatic pool cover. Automatic covers cover and uncover the pool by pushing a button which makes more convenience.
However, for those automatic covers, maybe, we need to come over pool to switch them on and off.  At that time,  you may just want a remote controlled antomatic pool cover. Have you ever thought about that you can use a remote controller to control the autoatic pool cover within a long distance?
We need a receiver box to install to motor of your pool cover and a transmitter to instruct the receiver to work.
This handy gadget can make high power AC motor rotate forward and reverse.

Here is the wiring picture:

Operation:
We aim to how to make this remote controllable automatic pool cover work in this step.  After wiring, we press button A to open pool cover with motor rotate in forward direction. Press button C, the motor stop rotating. We press button B to close pool cover with motor rotate in reversal direction. Press button C, the motor stop rotating.
Through remote controlling motor of pool cover rotate forward and reverse, we can control it open or close in a reliable distance anytime.

1 Channel High Power Long Distance Control Set Designed for Vacuum Motor

I have a central vacuum system. The motor is located in the garage. I want to be able to plug the motor into a receiver so I can turn it on and off from a wireless RF remote control. The garage is 100 ft from the house.
I try to use this high power long distance control set. S1PX-AC220-ANT2 & CB-2.
First I will prepare some materials. Transmitter and receiver, AC motor, power supply.
Wiring picture is as follow.
The AC motor connects to the receiver and the receiver is powered by 220V.

Pressing big button, the motor begins to rotate.

Pressing small button, the motor stops to rotate.

Remote Control 3 Phase Power Water pump

My friend has a pump that supplies his farm with water. The motor on the pump is 3.5kw and is 3 phase power. The pump fills a 5000 litre tank which lasts about a day. The on-off switch is roughly 1000m away from his house (no line of sight, lots of trees in-between). Recently, he wanted to know would he be able to connect it to the switch so that he can switch the pump on and off from home 1000m away? Why didn’t he choose remote control system to control the water pump?
I thought the method was feasible for him. So I suggested that he should buy a long range remote control system.
After several days, he showed me his device and installation.
With external extend antenna, this remote control unit can be long range controller. Transmitting distance is about 1000m. But how to remote control 3 phase power water pump? Besides the transmitter and receiver, we should prepare a relay which is applied to the pump, my friend told me. Here is the relay.

Let’s see how to install and operate.
Step 1, the relay should be connected to the receiver. Then three live wires are connected to the relay and power supply.
Step 2, another three live wires to connect the relay and water pump.
Step 3, power to the receiver. Pressing the big button of the transmitter, the receiver will receive an “ON” signal to instruct the reply and pump to pump water into the tank. Pressing the small button of the transmitter, the receiver will receive an “OFF” signal to instruct the reply and pump stop pumping water.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Channel Toggle Remote Control an 2400 Watts Electric Heater

A few day ago, I came up with a good idea when I stared at my electric heater. Why didn't I use remote controller to operate this 2400 watts electric heater? So I try to do what I think. I bought a remote controller with toggle mode on the internet . That is a high power remote control kit.

Let me show you how they work.

First, wire a power strip to the receiver and power supply. I used a power strip because I don't want to damage the plug and wires of the heater. (See the following picture)

Second, the receiver is powered by power supply.

Third, plug the electric heater to that power strip.

Pressing the button, the electric heater is turned on.

Pressing the button again, the electric heater is turned off.