Customized Time Delay Remote Controller for 6V Light

This 1 channel dc RF remote control switch features in controlling relay off time delay. Delay time can be customized according to actual requirement. It is widely applied to control lights, motors, fans, electrically operated doors / locks / windows / blinds or other electrical devices. It is activated in 6V power supply. You need provide us with the delay time you want when ordering. E.g. delay time: 20 seconds or 1 hour or 20 minutes… The delay time is not adjustable freely. Its working current is 10ampere and working distance is 100m (300ft).

It has normally open and closed contact. It controls various lights, fans or motors with voltage AC110~240V or DC0~28V. Here is the alternate current device wiring diagram and the wiring diagram of direct current device which not share the same power supply with receiver.

Of course, if you want to remote control direct current device which shares the same power supply with receiver, you need to do some different wiring from above wiring. Suppose that you want to remote control 6V lamp. So you don’t have to supply additional power for led lamp because led lamp will get power from powered receiver as long as you wire lamp to the receiver.
Here is the wiring procedure of 6V lamp which shares the same battery with receiver. The red wire from the lamp is connected to the C terminal of the receiver and black wire from the lamp is connected to the negative electrode of the power supply. The positive wire of the supply power is connected to B terminal and positive electrode of the receiver. The negative electrode of the power supply of power supply and receiver are connected together.

We set its delay time 20seconds.
Press button 1: Turn on the lamp. After 20seconds, turn off the lamp by itself.
During the delay time, press button 2: Turn off the lamp straightway.

How to Make a Remote Controlled 6V Doorbell

Question from customer:
I want to install a single channel remote to control my doorbell within the range of 150m. The old 6V doorbell was broken and I don’t want to repair the wires of doorbell. Ordinary wireless doorbell cannot be used because it doesn’t reach the distance I really want. I have an idea that a transmitter is connected to the doorbell button and relay in receiver is connected to doorbell. The only problem is the control range of remote need to reach about 150m. Would you like to recommend some favorable products?

Answer:
We recommend the 6V one channel 2000m receiver(S1U-DC06-ANT2) and long range transmitter (CB-1). Working voltage range of receiver is 6V. With normally open and close terminal, the voltage of the device being controlled is AC110~240V or DC0~28V. So it can be applied in 6V doorbell. Usually, you don’t have to supply additional power to doorbell because it can get 6V power from powered receiver when you connect them to the 6V power supply together. And the most significant is that it has extended external antenna which makes its control range up to 2000m (6000ft). You will be satisfied with this product.

According to your requirement, you can connect the button of the bell to the transmitter by two wires. Then connect the bell to the relay in the receiver.

Setting control mode Momentary: Connect Jumper-1.
When you press the button of the bell, RF signal will be sent out from transmitter to receiver. The receiver receives to turn on the relay, then the doorbell rings. Release the button, the doorbell stops ringing.

One Device Remote Control Another Device 6V 500M

Automation or automatic control is the use of various control systems for operating equipment as machinery, uses in factories, home. The biggest benefit of automation is that it saves labor, energy and material to improve quality, accuracy, efficiency and precision. Have you ever thought about home automation?
Someone wants to build home automation. Module 1 will connect to one existing device which make module 1 transmit RF signal to module 2 to indicate either “ON” state or “OFF” state. Module 2 will connect device which is ready to being controlled. When module receives the signal from module 1, it will turn on or off controlled device.
In fact, we have a completely new product 5~28V triggered great range transmitter of CB-2V which is applied for one device controlling another device. This transmitting module will be triggered by DC power 5~28V input. When your existing device is on, the transmitter will get power to send signal to receiver. We really hope this kind of remote can satisfy his needs.

We think our product can meet his need. According to his requirement, that transmitter can work  with dc 6V 1 channel latched long range receiver model of (S1L-DC06-ANT2). The receiver needs low voltage and current. Working voltage range of relay can be DC 0~28V. And The existing device will supply low current to activate transmitter. They work together to finish the automation.

Let’s study the wiring diagram. That is fairly simple. Existing device is connected to the positive and negative terminals of the transmitter. The device being controlled is connected to the normally open terminals “B”&”C” of receiver.



Or our receiver is activated by DC6V power. If the device he wants to control is also activated by 6V. We provide another wiring diagram to you.

When the transmitter got a voltage input from the working existing device, the transmitter will be triggered and send an “On” RF signal to the receiver. When the receiver received this signal, it will indicate the device being controlled to “On” state. Likewise, the existing device stops working and transmitter will send an “Off” RF signal to receiver. After receiving the signal, the receiver will indicate the device being controlled to ‘Off” state.

Horn Starting System is Remote Controlled

Question from customer:
I would like some help to make my Horn starting system become remote controlled. At present I have a momentary switch on a 12 foot cable when the switch is press it activates the horn. I would like the horn and housing to be separated. I would like the horn to be approximately 100M away. Which of your products will help me? In the future I would like to add a 2nd and 3rd horn to my set up which will be housed in separate boxes.

Answer:
If you want to remote control a horn, we recommend the long range 1 channel 12V momentary receiver (S1XM-DC12-ANT2) and the long range transmitter CB-1. It is direct power output; control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. Its working distance can reach 2000m with external extended antenna.

Here is the wiring diagram. Wire horn to A&B terminals and supply 12V power to the receiver. There is no need to supply additional power to horn because horn can get power from powered receiver.

After wiring, here comes the operation. Momentary mode is the only working mode in it.
Press and hold button: Turn on the horn; Release the button: Turn off the horn.
If you want to remote control 2~3 horns, we recommend 2~3 receivers S1XM-DC12-ANT2 and another two transmitters, one is two-button long range transmitter CB-2 or three-button long range transmitter CB-3.

How to Remote Control 6V LED Lights

Question from customer:
I’m looking for a wireless remote that I can use to create a simple on off switch to 12 led light fixtures connecting to a 6V battery at different places around my home. Do you have any suitable remote controller for me?

Answer:
We recommend model 12 Channel DC6V Remote Controller – 1 Transmitter & 12 Receiver  (12S1UB-DC06&1CV-12). This RF remote controller has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. That is to say, you only need a transmitter to control 12 receivers. 6V is added to receiver as activated power. It operates in toggle, momentary, and latched mode (set the mode as you like freely). It is great for hard to reach lights or other DC/AC electrical devices, remote distance can be 500m (theoretically). And it is applied for controlling lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

Here is the wiring diagram. LED lamp is connected to normally open terminals B&C. And add a wire between terminals “B&-“ and another wire to terminals “C&+”. At last, wire a plug to terminals “+&-“. LED lamp and receiver will share the same power supply——6V.

It’s easy to set and operate. You can press each button on the transmitter to control the corresponding receiver to control LED lamp.

DC12V Remote Switch Controls Winch Motor Rotation and Lamps On and Off

Question from customer:
I am in need of a controller. I will be using this to control a winch on my pickup and some lights. So I need one button momentary for line in, one button momentary for line out, and 2 buttons on/off for lights.
Answer:
4 Relay multi-mode On / Off remote controller (S4U-DC12 & C-4) is very suitable to you. There are 4 channels for more than one device. It has universal controlling mode, including toggle, momentary, latched, and Momentary+toggle modes. The maximum current is 10A and working distance is about 100m. It features in controlling lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with AC110~240V or DC0~28V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors.

According to your requirement, Channel 1~2 are for motor and Channel 3~4 are for lamps. At first, please see the wiring. Wire winch motor to “B” terminals of relay 1 and relay 2. That makes motor rotate in two different directions. Supply power to winch motor. Secondly, wire two lamps to “B” terminals of relay 3 and relay 4. Supply power to lamps.

Thirdly, learning Momentary (Channel 1~2) + Toggle (Channel 3~4) control mode: When the receiver is in the status of LEARNING, press button 3 of the transmitter.
When you press and hold button 1, winch motor rotates in positive direction; release it, winch motor stops.
When you press and hold button 2, winch motor rotates in reverse direction; release it, winch motor stops.
When you press button 3, turn on lamp 1; press button 3 again, turn off lamp 1.
When you press button 4, turn on lamp 2; press button 4again, turn off lamp 2.

Underground Garage Door is Controlled Car Alarm System

Question from customer:
I need a radio system for switching a receiver of an underground garage, by a concrete slab with steel reinforcement and about 30 meters Distance 1st floor. The receiver may be 220 volts. Transmitter I want to act with an external contact. (Connection to a car alarm system).
Answer:
We recommend the 1 channel high power receiver (S1PUA-AC220-ANT2) and long range transmitter with extended wires (CB-2N). The receiver is activated by ac 220V, which is about 2000m working distance with external extended antenna. The wireless RF signal can pass through walls, floors and doors. It works with the long range transmitter, which features in two external wires because connection of two wires is its triggering method.

According to your requirement, we drew a wiring diagram.

Wires on the transmitter should be connected to the contacts of car alarm system.

The normally open contacts A&B of receiver should be connected to the garage door motor. And supply additional 220V power other than receiver.
Setting latched mode to this receiver.
When the contacts of two wires are closed, the transmitter is triggered and then transmits an rf signal “ON” to activate the receiver. After the receiver receives the signal, contacts A&B are closed; the motor starts to work to open the garage door.
When the contacts of float switch are cut, the transmitter is triggered and then transmits an rf signal “OFF” to deactivate the receiver. After the receiver receives the signal, contacts A&B are cut; the motor stops working to shut down the garage door.

Latched Mode Remote Controller Apply for Device Control Another Device (Float Switch control Water Pump)

Question from customer:
When the tank is empty my float switch makes contact and stays in this mode till the tank is full.
What I need is for the transmitter to activate the receiver and hold it in the on position till the float switch interrupts the transmitter and releases the receiver. I need a receiver which is only activated as long as the transmitter sends a signal. Or I need a way to make the transmitter send a signal when the float switch makes contact, then interrupts this signal and sends a second signal when the float switch interrupts contact.


Answer:
We recommend the model of normally open latched 2000m remote controller (S1L-DC12-ANT2 & CB-2N). The receiver is with magnetic antenna and only one working mode—latched mode. It is activated the 12V power. The transmitter is designed with novelty. There are two wires extending from transmitter. The triggering method is connection and disconnection of two wires. When two wires are connected, “ON” signal will be sent out. When two wires are connected, “OFF” signal will be sent out.

Wires on the transmitter should be connected to the contacts of float switch.

The normally open contacts B&C of receiver should be connected to the water pump.

When the tank is empty, the contacts of float switch are closed, the transmitter is triggered and then transmits an rf signal “ON” to activate the receiver. After the receiver receives the signal, contacts B&C are closed; the pump starts to work.
When the tank is full, the contacts of float switch are cut, the transmitter is triggered and then transmits an rf signal “OFF” to deactivate the receiver. After the receiver receives the signal, contacts B&C are cut; the pump stops working.

315Mhz/433Mhz 9v Remote Controller for Electron Microscope’s Motors

Question from customer:
I use a manual switch to control 4 9V motors of my electron microscope and each motor works in 150ma (0.15a). In addition, only one motor works when I press button of remote control each time. Now I want to remote control them, have you got any suitable remote for me?
Electron microscope:

Manual Switch of microscope:

Answer:
We thought this 8 channel rf remote transmitter & receiver is very suitable for you . It can be used to control at most 8 on / off electrical devices. With characteristics of strong anti-interference, reverse power protection and over current protection. Three voltages dc9v, dc12v and dc24v are provided to choose. It is widely applied to control many kinds of lights, electrically operated doors / gates / windows / blinds and so on. It works with 8-button transmitter and their transmitting distance can reach to 500m.

This is the wiring diagram.

Wire each motor to the normally open terminal “B”. According to the diagram, you can do wiring like above. Even though there are 8 working modes in it, you can choose ”Momentary mode” which is applied in motor’s rotation.
Control mode Momentary (Channel 1~8): Press and hold -> On; Release -> Off.

Press and hold button 1: Motor 1 rotates in positive direction
Release button 1: Motor 1 stops rotation
Press and hold button 2: Motor 1 rotates in reverse direction
Release button 2: Motor 1 stops rotation

Press and hold button 3: Motor 2 rotates in positive direction
Release button 3: Motor2 stops rotation
Press and hold button 4: Motor 2 rotates in reverse direction
Release button 4: Motor 2 stops rotation

Press and hold button 5: Motor 3 rotates in positive direction
Release button 5: Motor 3 stops rotation
Press and hold button 6: Motor 3 rotates in reverse direction
Release button 6: Motor 3 stops rotation

Press and hold button 7: Motor 4 rotates in positive direction
Release button 7: Motor 4 stops rotation
Press and hold button 8: Motor 4 rotates in reverse direction
Release button 8: Motor 4 stops rotation

Only one motor works when you press the corresponding button on the remote.

220V Transceiver Turn on/off LED Lamp Via Transformer

Question from customer:
I want to put a 220v Transceiver to turn on / off the power of a transformer of led lighting (to avoid the transformer is always on), this will make me a remote control switch. I want a basic on / off function product.
Answer:
1 channel ac power direct output remote switch (S1X-AC220+C-2) is suitable for you. Its remarkable feature is ac power direct output, that is to say, you don’t have to supply additional power to being controlled device because it can get power from powered receiver. It controls lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with AC 100~240V range. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance (about 100m); the wireless RF signal can pass through walls, floors and doors.

Wiring diagram is here. Wire transformer to L&N terminals of “OUT “ terminal. Then wire lamp to the transformer.

To avoid transformer being always on, you can use transmitter to remote control it. There are three working modes in it. They are toggle, momentary and latched modes. Here, you can choose latched because there are two buttons of transmitter.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press button 1: Turn on the transformer, terminal OUT outputs AC power to switch on lamp.
Press button 2: Turn off the transformer, terminal OUT no output to switch off lamp.