Lawnmover Motor is Controlled Remotely

Question from customer:
I’m looking for an RC transmitter and receiver to operate the 4″ actuator a distance of 200ft for steering a lawnmower. Any suggestions?

Answer:
We recommend the model of 500m/1500ft RF motor controller (S1FC-DC09/12/24 & CV-4-2). The controller is activated by DC 9V, 12V and 24V. It is usually for motors of rolling blinds, doors, projection screens, awnings, pumps, winches, conveyor or other appliances and mechanicals. It features in forward-reverse-stop capability which can make motor rotate in positive or reversal direction. With maximum transmission distance of 500m/1500ft, it can satisfy your requirement. Inner circuit of this kit uses the RF technology for making a wireless remote, which can make motor controlled by transmitter from any places with in reliable distance, this configured wireless signal can pass through walls, doors or floors or other solid obstacles.

Here is the wiring.
At first, we connect power line to terminals “+” and “－”. Secondly, we connect the receiver to the lawnmower actuator motor. Lawnmower actuator motor is wired to UP and DOWN terminals of receiver. At last, we add power supply to receiver. You can exchange “UP” and “DOWN” lines of the motor to change rotating direction of the motor.

There two working modes in it.
Set Momentary control mode: Do not connect Jumper.
Press and hold button ▲ on remote or receiver: Terminals UP and DOWN output ＋ DC9V / DC12V / 24V (UP: ＋, DOWN: －), lawnmower actuator motor rotates continuously in positive direction.
Release button ▲ on remote or receiver: Stop the motor.
Press and hold button ▼ on remote or receiver: Terminals UP and DOWN output － DC9V / DC12V / 24V (UP: －, DOWN: ＋), lawnmower actuator motor rotates continuously in reversal direction.
Release button ▼ on remote or receiver: Stop the motor.

Set Latching control mode: connect the Jumper.
Press button ▲ on remote or receiver: Terminals UP and DOWN output ＋ DC9V / DC12V / 24V (1: ＋, 2: －), lawnmower actuator motor rotates continuously in positive direction.
Press ■ on remote or receiver: Stop the motor.
Press button ▼ on remote or receiver: Terminals UP and DOWN output － DC9V / DC12V / 24V (1: －, 2: ＋), lawnmower actuator motor rotates continuously in reversal direction.
Press button ■ on remote or receiver: Stop the motor.

Why RF Remote Controller

Why RF Remote Controller

2 Channel Power Outage Memory Function Remote Controller

We recommend this 2 channel power-off memory function remote controller (S2MU-DC06/09/12/24 & C-2). It can work in 4 kinds of voltage, 6V, 9V, 12V and 24V. There 4 working modes in it. You can switch as you want through connection or disconnection of jumpers. It controls lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V. It is great for hard to reach lights or other DC/AC electrical devices. The working transmission is about 100m in the open field. With function of memory, if the power is cut off, the relay will return automatically to the previous status after the power is restored.

We’d like to show the wiring and controlling of ac, dc lamps.
The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp or dc lamp to normally open contact B&C and supply AC 220V power or dc power to lamp.



Usage:
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle: Press -> On; Press again -> Off.
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary: Press and hold -> On; Release -> Off.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, another relay Off; Press another button -> Off.

Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.
Control mode Momentary (Channel 1): Press -> On; Press again -> Off.
Control mode Toggle (Channel 2): Press and hold -> On; Release -> Off.

Wireless Remote Control Motor

Item link:
http://www.ourautomation.com/ac-100240v-motor-momentary-remote-control-transmitter-receiver-p-1505.html

www.ourautomaton.com

How to Remote Control 4 Lamps from Different Places

One of our customers wants a simple wireless remote operate 4 led lamps from several room at his house. He needs 4 transmitters and a receiver which can be mounted in a designated place. The remote must work from receiver about 50m away and not line of sight through doors and walls.
We suggest him choose dc 4 channel remote control system (S4C-DC12& 4C-1). Maximum working current is 5amp each relay. Working distance of remote and receiver set is about 100m (300ft) in open field. This 4CH 6V9V/12V/24V wireless remote switch operates in toggle, momentary, latched, toggle + momentary control mode (set the mode as you like freely). Easy to install and operate. Just press slightly the button on the remote, you can control universal DC/AC electrical devices. The RF signal can pass through walls, doors and other barriers. As he said, we will set 4 transmitters and this receiver with same 8-bits code in advance so that they can work together.

Operation modes:

• 1) Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched (Relay 1~4): Press -> On, other relays Off; Press other button -> Off.

• 2) Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary (Relay 1~4): Press and hold -> On; Release -> Off.

• 3) Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle (Relay 1~4): Press -> On; Press again -> Off.

• 4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Relay 1, 2): Press and hold -> On; Release -> Off.
Control mode Toggle (Relay 3, 4): Press -> On; Press again -> Off.
We will show you how to remote control 4 led lamps from different places.

Wireless Controller Switch DC Lamp Off/On and Make Motor Run in Positive and Reverse Rotation

We are about to recommend remote controller which is applied to both motor and lamp. It is DC12V momentary &toggle remote controller (S1F-DC12 & C-3-2), which features in motor forward-reverse capability. You can rotate the motor in positive or reversal direction by transmitter from any place within a reliable distance, wireless signal pass through walls, floors and doors. It is suitable for the motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V. We also design lamp controlling function so that you can control motor and lamp with the same transmitter.

 

Wireless Wall Switch and AC Receiver Remote Control Home Lamp

We made a remote control kit which consists of a wall-mounted switch and a remote receiver (S1X-AC220&HR-1).

When we use ordinary switch to switch home appliances off and on, we should do some wiring for home appliances, some time it is very complicated and time- consuming. Our RF wireless wall mounted switch looks like universal switch from appearance, but it is wireless and operate by RF signal that can pass through walls, floors and doors. It is can be simply affix to any place you want by double faced adhesive tape.

Through RF signal, you don’t have to wire between switch and appliances. Wall-mounted switch works with remote receiver to remote control ac lamp.
Here is the wiring diagram.

Wire ac lamp to OUTPUT of receiver. And add power supply to receiver. This kind of receiver is designed for AC output terminals so that lamp can get power from output terminals of receiver directly.
Setting different control modes (We usually set toggle for lamp controlling.)
Setting control mode Toggle: Only connect Jumper-2.
Press button: Turn on the relay, terminal OUT outputs AC power, turn on lamp.
Press button again: Turn off the relay, terminal OUT no output, turn off lamp.

Wireless WIFI Controller for Linear Actuator

Wireless Motor Controller for Linear Actuator Motor

“I need a linear actuator to hook to my home automation. I control my large saltwater tank via this system. I want to achieve:
Small actuator on cabinet door
When I turn an outlet on that it’s plugged into actuator opens
Ability to turn outlet off and actuator closes”

Answer: 
“You can use our controller- low current triggered transmitter (CB-2V) and forward-reverse-stop receiver (S1FC-DC12). The transmitter is low-current triggered. When input DC power 5~28V, the transmitter is triggered and then transmits an rf signal “ON”. When stop inputting DC power, the transmitter is triggered and then transmits an rf signal “OFF”. This DC RF motor remote control features in forward-reverse-stop capability. You can rotate the motor in positive or reversal direction by transmitter from any place within a reliable distance, wireless signal pass through walls, floors and doors. It is suitable for the motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals. Remote distance is up to 500M.

Firstly, we connect transmitter to a 12V power adapter and plug to adapter the outlet, and secondly, connect the receiver to the linear actuator motor. Linear actuator motor is wired to UP and DOWN terminals of receiver. Finally, add power supply to receiver.

When you turn the outlet on, the transmitter sends a signal “ON” to the receiver, then actuator shaft extends.
When you turn the outlet off, the transmitter sends a signal “OFF” to the receiver, then actuator shaft retracts.”

One to Many Series-One Transmitter Remote Control 4 Devices

Question from customer:
“I need to operate 3 or 4 devices separately with 2 momentary functions per each. I need one transmitter to function from approx. 100 – 500m – to work all devices. The devices will operate on a 12volt DC system.”
Answer: 
We recommend the 2 channel 2000m wireless momentary receiver (S2M-DC12-ANT2) with external antenna, and the long rang transmitter (CB-2). It can control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with AC110~240V or DC0~28V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. It is momentary mode (Press and hold→On; Release→Off). External Extended antenna, its transmitting can reach about 2000m.

You can wire 4 devices to each relay of two receivers respectively. Two receivers and this transmitter will be set the same code. This receiver is NO/NC contact. Wire device to B terminals to each relay. And supply power to receiver your device respectively.

1) Press and hold big button: Turn on relays on the first receiver (connect B and C, disconnect A and B)
2) Release big button: Turn off relays on the first receiver (disconnect B and C, connect A and B)
3) Press and small button: Turn on relays on the second receiver (connect B and C, disconnect A and B)
4) Release small button: Turn off relays on the second receiver (disconnect B and C, connect A and B)

Wireless Remote Control Electric Door Locks

Question from customer:
I need one transmitter and 2 receivers that the transmitter operates separately. Preferably 12 volt receivers will work out to 300 yards. I am using the receivers to operate door locks on a project I’m working on.
Answer:
We recommend you 2000m remote control system input & output 12V (S1X-DC12-ANT2&CB-2). One transmitter (CB-2) can pair up with 2 receivers (S1X-DC12-ANT12), so you can use one transmitter remote control two receivers. With external extend antenna, its transmitting distance can reach about 2000m (2187yards) in the open field. It is 12volt actuated, that is to say, electric door lock doesn’t need to be supplied additional power supply because electric door lock will get power from powered receiver.

Wiring is simply easy. Wire your electric door lock to A&B terminals of receiver.

Operation:
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay, terminal A&B output DC power, open the door.
Press small button: Turn off the relay, terminal A&B no output, close the door.

Four Transmitter and One Receiver-One to Many Series

Question from customer:
I need a unit that can receive from four transmitters, and switch 4 relays. Each transmitter controls each channel.
Answer:
We recommend the model of 4 Transmitters and 1 Receiver Kit (S4C-DC12 & 4C-1), which belongs to “One-to-many series”. “On-to-many series” include one-transmitter-to-many-receiver system and one-receiver-to-many-transmitter system. It is often used for controlling two or more electrical devices in different places by one transmitter; or one electrical device by two or more transmitters.
If you want to remote control one device with different transmitter from different places, this kit is your better choice.

Here is the wiring diagram for your reference.
The receiver is normally open & closed contact. A,B terminals are normally closed. B,C terminals are normally open. So you can wire your devices to B terminals and negative terminal of power supply. And add DC 0-28V or AC 110-240V to your devices. Supply DC 12V to receiver.

Its transmitting distance is about 100m (in the open field). You can set different working modes according to your need.
1) Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched (Relay 1~4):
Press transmitter 1, light 1 ->On; other lights Off;
Press transmitter 2, light 2 ->On; other lights Off;
…
2) Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (Relay 1~4):
Press and hold button of any transmitter-> light is on;
Release button -> light is off.

3) Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (Relay 1~4): Press button of any transmitter -> light is on;
Press button of any transmitter again -> light is off.

4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.
Control mode Momentary (Relay 1, 2):
Press and hold buttons of transmitter 1 or 2 -> light 1 or light 2 is on;
Release buttons of transmitter 1 or 2 -> light 1 or light 2 is off.

Control mode Toggle (Relay 3, 4):
Press buttons of transmitter 3 or 4-> light 3 or light 4 is on;
Press buttons of transmitter 3 or 4 again -> light 3 or light 4 is off.

How to Build Communication between Karaoke Rooms and Reception Desk

Question from customer:
I want to run business of karaoke rooms. So I need a set to be installed in karaoke rooms and reception desk. It is better to install calling gadget to karaoke room and receiver to reception desk. When there is customer in karaoke room calling, he can using calling gadget to call our stall to help him. Do you have any suggestion?
Answer:
We recommend wireless calling system to you. It includes calling transmitter and receiver host. You can pair up any kinds of calling transmitter with receiver host according to your need. The receiver host is 999-channel, so you can pair up 999 transmitters with a 999-channel receiver host at most. This kit is multi-mode. It is better to choose “Normal mode”. You can choose 200m 2 buttons free sticker wireless calling button and a 999- channel receiver host and stick calling button on the wall of karaoke room.
Here we can show you this controlling project procedure.

 

Wireless Calling System (Hospital Mode)

Question from customer:
I manage a small new hospital. Now I want a remote control system which includes six remote transmitters and one 6-channel receiver. Each remote controller is put on every desk beside bed. And the receiver is put in the nurse station. When there is patient calling, he can press the button to notify the nurse station in time.
Answer:
We recommend wireless calling system. They include a 999-channel receiver host and more than one transmitter at your option. You can choose six calling buttons That is to say, you can pair up 999 transmitters with a 999-channel receiver host at most. This kit is multi-mode. We’d like to make a presentation of hospital mode.

AC 220V Output Remote Controller for AC Solenoid Valve

Remote Control Electric Fireworks Momentarily

AC 220V Output Remote Controller for Electric Shutter

Overview:
I want to buy a radio system for my 9 shutters (220 V), wireless control, 9 receivers and 1 remote, climb or descend in all my components by one remote.

Solution:
We recommend ac power output controller (S1FM-AC220), which is designed for controlling motor specially. It can remote control many kinds of motor, rolling blinds/ doors, projection screens, awnings, winches, conveyors… 10amps is its maximum current. And when it works with the long distance transmitter (CB-2), the whole kit’s transmitting distance will reach 1000m.

Connect live wire to terminal “L” and neutral wire to terminal “N”. Then connect AC motor to terminals “UP”, “COMMON” and “DOWN”. You can exchange “UP” and “DOWN” wires of motor to change rotating direction of motor. 9 shutter motors should be wired to 9 receivers respectively. 9 receivers will be programmed the same code so that they can work together with one remote.

There is only one working mode in this controller. It is inversion control mode(Press and hold big button→positive rotation; press and hold small button→reversal rotation )
Press and hold big button, terminals UP and COMMON directly output AC 220; 9 shutter motors rotate continuously in positive direction at the same time.
Release big button, stop 9 shutter motors simultaneously.
Press and hold small button, terminals DOWN and COMMON directly output AC 220; 9 shutter motors rotate continuously in reverse direction at the same time.
Release small button, stop 9 shutter motors simultaneously.

Run RC Motor Forward and Backward Wirelessly

Overview:
My plan is to be able to remotely control an RC motor forward and backward wirelessly with the remote. I was thinking one receiver and one remote, but which products would I be able to do this with.
Solution:
We recommend the model of DC power motor controller (S1FC-DC12&CV-4-2) to you. This DC RF motor remote control features in forward-reverse-stop capability. You can rotate the motor in positive or reversal direction by transmitter from any place within a reliable distance, wireless signal pass through walls, floors and doors. It is suitable for any RC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals. The kit’s transmitting distance is up to 500M.

Connect power wire to terminals “+” and “－”. Connect DC radio-controlled motor to terminals “UP” and “DOWN”. You can exchange “UP” and “DOWN” wires of the motor to change rotating direction of the motor.

Set Momentary control mode: Do not connect Jumper.
Press and hold button ▲ on transmitter or receiver: Terminals UP and DOWN output +DC12V (UP:+, DOWN:—), RC motor rotates continuously in positive direction.
Release button ▲ on transmitter or receiver: Stop the RC motor.
Press and hold button ▼ on transmitter or receiver: Terminals UP and DOWN output +DC12V (UP:—, DOWN:+), RC  motor rotates continuously in reverse direction.
Release button ▼ on transmitter or receiver: Stop the RC motor.
Set Latched control mode: connect Jumper.
Press button ▲ on transmitter or receiver: Terminals UP and DOWN output +DC12V (UP:+, DOWN:—), RC motor rotates continuously in positive direction.
Press button ■ on transmitter or receiver: Stop the RC motor.
Press button ▼ on transmitter or receiver: Terminals UP and DOWN output +DC12V (UP:—, DOWN:+), RC motor rotates continuously in reverse direction.
Press button ■ on transmitter or receiver: Stop the RC motor.

2000m Momentary Controller for DC Motor

Question from customer:

I am looking for a radio transmitter receiver 1 channel, 24V, 500 to 1000m, and function: I support the button, close the relay; I loose the button, open the relay.

Answer:

We recommend the model of 1 channel Momentary 2000m remote control kit (S1M-DC24-ANT2& CB-1). Remote control kit with momentary mode is often used to control motor open/close for electrically operated door/lock/window/blind. Press and hold the button on transmitter, start the motor (close the relay); release the button, stop the motor(open the relay). With external extend antenna, its working distance can reach 2000m (6000ft) theoretically. We have three standard voltage: 9V, 12V, 24V. You can choose the 24V. Owing to one relay on the receiver, it won’t realize that DC motor runs in forward and reverse. It only switches off/ on DC motor.

And it is normally open and close relay contact, generally speaking, you should add additional power supply to controlled DC motor. Or you can use one power supply for receiver and DC motor at the same time. The wiring method is as follow.

Connect DC motor to B&C terminals. And wire motor to positive and negative terminals of battery. Wire positive and negative terminals of receiver to battery.

Operation is very easy.

Press and hold button, turn on motor.

Release button, turn off motor.

How to Remote Control 5 Lamps Individually

Question from Customer:
I am looking for 5 remote controls to control 5 individual lights in living room. Do you have any recommendations?

Answer:
We recommend the model of 1 channel 220V power output controller switch (S1X-AC220+2C-2), you can buy 5 sets.
It can control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with AC 100~240V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance (about 100m); the wireless RF signal can pass through walls, floors and doors. With characteristics of direct power output, you don’t have to provide additional power to remote-controlled device since device can get power from receiver if receiver is charged.

Wiring diagram is here. Wire light to L&N terminals of “OUT “terminal. Each light will wired to each receiver.
There are three working modes in it. They are toggle, momentary and latched modes. Here, you can choose latched because there are two buttons of transmitter.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press button 1: Turn on light.
Press button 2: Turn off light.
You can switch off/ on any light at your option.

9V 999-Channel Calling Receiver Host for any calling

Wireless calling receiver host system adopts RF wireless and computer communication technology. It can easily pair up to 999 wireless calling transmitters and 1 manager remote controller. The receiver host uses advanced industrial micro processor and high-sensitivity superheterodyne receiving technology which make products very stable.

At the same time, the wireless calling receiver host has advanced number speaker function and it can clearly read the number, function, room number and so on. It is compatible for different working mode, suitable for different places.

We offer four kinds of power adaptors at your option.

Bracket from the back of receiver can support receiver to stand on the table stablely. Or with fixed holes on the back of receiver, you can use screws to install it on the wall.

 

It can pair up many kinds of calling button to build up wireless calling system for waiter calling, emergency calling and so on. The wireless calling system has millions of different code which can be paired easily and freely.

And it is widely used in restaurant, cafe, bar, tea shop, KTV, bank, office, factory, hotel, hospital health clubs, beauty salon, spa center and so on.

It includes many benefits, reducing staff costs, enhancing the service experience and staff efficiency, increasing revenue.

Wireless Standard Light Switch and RF Receiver for AC Lamp

Question from customer:
I want switch on and off my porch light. But I don’t want do some wiring from porch to inside of my house. I want switches which can be mounted or glued to a wall. I’d like to use standard light switch fixtures as well if possible.
Can you recommend me anything that solves this situation?
Answer:
We’d like recommend this 6VDC 1 button wireless calling button with adhesive-tape and 1 channel AC220V receiver (S1X-AC220). Calling button is a part of wireless calling system, here we pair it with a wireless RF receiver to make a remote control system.

Wireless calling button is the hi-tech electronic product which is integrated wireless communication and computer technology. Usually it pair with a wireless receiver host. However, ordinary RF receiver can work with it too as long as they paired.
It is widely applied to restaurants, coffee shops, karaoke rooms, discos, sauna rooms, beer houses, pubs, night clubs, bowling alleys, golf courses, video halls, hotels, hospitals, schools, chain stores ,shops…
Wireless calling button simply stick to wall or desk by double-adhesive tape on its back. You can stick to anywhere you want. There is no need wiring from switch to lamp. Your light can be wired to the receiver and do not need supply additional power to light because it can get power from receiver.
Here is the receiver wiring diagram.


Press the “CALL” button, turn on porch lamp.
Press the “CALL” button again, turn off porch lamp.

Triple Function of Vibrator and Beeper

Tri-mode RF wireless remote vibration & beeper kit (Z-06+C-1). There are three working modes for this gadget. They are vibration, beep and vibration + beep modes. It can be used in calling, animals training, alert device, reminder…

Motor Running Timing Setting of LED Tube Circuit Board Controller

Timed Digital Tube Circuit Board Control Motor's Rotation

High Power Winch Motor Remote Controlling

Question from customer:
Hi, I am looking for a 110 volt remote control for a winch that pulls my boat from the water into my boat house.
Requirements:
120 volt
20 amps max
Momentary switches
Do you have a kit that meets these requirements?

Answer:
First, we’d like to recommend motor momentary remote controller (S1FM-AC220&CV-2-2). It can remote control motors of rolling blinds/ doors, projection screens, awnings, pumps, winches, conveyors or other electric appliances and machineries. With 2 directive buttons ▲(Positive rotation) and ▼(Reversal rotation), you can rotate the motor in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance(this kind of remote controller is 500m/1500ft). Power supply is AC 100~240V. But this maximum current is 10amps, it is not enough for you to remote control your 20amps winch. So we’d like show you contactor motor starter relay, you can use it amplify current which you need. AC contactor (aka motor starter) is a high capacity relay. It is often used to control a motor or as a main power switch. It’s used for long range connection and circuit disconnection, frequent activation and controlling AC motor.

Here is the wiring diagram. Two contactors will act as a bridge between remote controller and high power motor to help activate high power motor to rotate in positive and reversal position.

Wire A1 terminal of contactor 1 to UP terminal of receiver, and A1 terminal of contactor 2 to DOWN of receiver. Wire T2 terminals of contactors 1&2 to winch motor. Wire winch motor to COM terminal of receiver. Supply power to receiver and contactor 1&2 respectively.
Operation:
Press and hold button ▲ on remote: Motor rotates continuously in positive direction.
Release button ▲ on remote: Stop the motor.
Press and hold button ▼ on remote: Motor rotates continuously in reversal direction.
Release button▼ on remote: Stop the motor.

Digital Tube Electric Board Temperature Control Setting and Remote Controlling Motor

This product is 12VDC power input. 

With manual control function, remote control function, temperature control function for automatic working, it can be used in various fields, including industry and household.  

Control System is widely used to control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances.

There are 2 working modes in it. Momentary mode and Latched Mode

Working distance is about 100m.

 

Video of Digital Tube Electric Board Temperature Control Setting :

 

Video of Digital Tube Electric Board Temperature Remote Controlling Motor

 

 

 

Phone Smart GSM Power Socket

This tri-frequency/tri-band GSM smart power socket has manual control, state checking function and power-off memory function other than phone call remote control and SMS remote control.

Manual Control
Press buttons SW1/SW2/SW3 on the socket directly to remote control the socket. Press SW1, socket 1 is socket 1 is power-on state. Press SW1 again, socket 1 is power-off state. Press SW2, socket 2 is power-on state. Press SW2 again, socket 2 is power-off state. Press SW3, socket 3 is power-on state. Press SW3 again, socket 3 is power-off state. When devices are plugged into sockets, only press buttons on the socket, you can switch on or off those devices.

CHECK command: Check the state of the socket
Edit text message “SN+ Six passwords +CHECK” and send to socket. You will receive the state of the socket. Then you will know the ON or OFF state of each socket.

Power-off Memory Function of Socket
The power-off memory function of socket is default in socket.
The STA 1 light flashes twice after power is on. It means that the state is power-off memory function is saved.
The STA 1 light flashes 4 times after power is on. It means that the state is power-off memory function is not saved.
Power-off state can be changed by the customer. Press SW1 for 12 seconds then release, you can change the current memory state.
Note:
This product can only control power supply on or off and do not have other functions. If some devices don’t have power-off memory function of it, even you want to start it by using this socket, it won’t work immediately. You have to turn on its own switch to restart it.
Reset to default
Press the SET button and SW1 button at the same time for 1 second, the STA1 light will flashes twice slowly. You reset socket successfully.
The previous preset owner number will be deleted and password becomes six zeros: 000000. The three switches are also disconnected.

How to Use Phone to Remote Control Devices On and Off

Our new product mobile phone GSM smart power strip is used in many fields, for example industry or household. It is applied to air conditioner, electric heaters, water pump, motors, fans, servers, relay station, TVs, water heaters, electric doors, rice cookers, lamps, speakers or other devices with voltage AC110~220V. Or something special remote controlling, you can also feed your pet via this GSM switch. How to use this socket on earth? Let’s see the following procedure.

Here we want to introduce “Phone call Remote Controlling” method.
When you use the owner number to dial, the phone will be gotten through after 2 seconds. Voice prompt: “Welcome to use the smart socket. Please enter the password and end up with “octothorp”. Then do follow the voice prompt. When your password is correct, the voice prompts is “The password is correct”. If your password is correct, you can remote control devices which are plugged into those sockets via your mobile phone or fix telephone. This product can only control power supply on or off and do not have other functions. So you can only turn on and off devices.
When you input the password with illegal format or even wrong password, the voice prompts is “The password is wrong, please input again” .You are allowed to input password incorrectly three times. If more than three times, the voice prompt is: “Thank you for using, goodbye” and hang up after 2 seconds.
Attention: Socket can be controlled many times. When you want to stop controlling, press asterisk (star key) and octothorp (hash key), the voice prompts is “Thank you for using, goodbye” and hang up after 2 seconds.

Customized Time Delay Remote Controller for 6V Light

This 1 channel dc RF remote control switch features in controlling relay off time delay. Delay time can be customized according to actual requirement. It is widely applied to control lights, motors, fans, electrically operated doors / locks / windows / blinds or other electrical devices. It is activated in 6V power supply. You need provide us with the delay time you want when ordering. E.g. delay time: 20 seconds or 1 hour or 20 minutes… The delay time is not adjustable freely. Its working current is 10ampere and working distance is 100m (300ft).

It has normally open and closed contact. It controls various lights, fans or motors with voltage AC110~240V or DC0~28V. Here is the alternate current device wiring diagram and the wiring diagram of direct current device which not share the same power supply with receiver.

Of course, if you want to remote control direct current device which shares the same power supply with receiver, you need to do some different wiring from above wiring. Suppose that you want to remote control 6V lamp. So you don’t have to supply additional power for led lamp because led lamp will get power from powered receiver as long as you wire lamp to the receiver.
Here is the wiring procedure of 6V lamp which shares the same battery with receiver. The red wire from the lamp is connected to the C terminal of the receiver and black wire from the lamp is connected to the negative electrode of the power supply. The positive wire of the supply power is connected to B terminal and positive electrode of the receiver. The negative electrode of the power supply of power supply and receiver are connected together.

We set its delay time 20seconds.
Press button 1: Turn on the lamp. After 20seconds, turn off the lamp by itself.
During the delay time, press button 2: Turn off the lamp straightway.

How to Make a Remote Controlled 6V Doorbell

Question from customer:
I want to install a single channel remote to control my doorbell within the range of 150m. The old 6V doorbell was broken and I don’t want to repair the wires of doorbell. Ordinary wireless doorbell cannot be used because it doesn’t reach the distance I really want. I have an idea that a transmitter is connected to the doorbell button and relay in receiver is connected to doorbell. The only problem is the control range of remote need to reach about 150m. Would you like to recommend some favorable products?

Answer:
We recommend the 6V one channel 2000m receiver(S1U-DC06-ANT2) and long range transmitter (CB-1). Working voltage range of receiver is 6V. With normally open and close terminal, the voltage of the device being controlled is AC110~240V or DC0~28V. So it can be applied in 6V doorbell. Usually, you don’t have to supply additional power to doorbell because it can get 6V power from powered receiver when you connect them to the 6V power supply together. And the most significant is that it has extended external antenna which makes its control range up to 2000m (6000ft). You will be satisfied with this product.

According to your requirement, you can connect the button of the bell to the transmitter by two wires. Then connect the bell to the relay in the receiver.

Setting control mode Momentary: Connect Jumper-1.
When you press the button of the bell, RF signal will be sent out from transmitter to receiver. The receiver receives to turn on the relay, then the doorbell rings. Release the button, the doorbell stops ringing.