Hot Posts

2013/08/30

2000M 4 Channel DC 9V 12V 24V RF Remote Control Switch 10A

This is the 4 channel multi-mode dc RF remote control kit. Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC110~240V or DC0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors.
There are 4 working modes for your requirement. With the external extend antenna, its working distance can reach 2000m(6000ft) in open field.

Operational Video:

2013/08/28

Remote Control RV's Flood Lights

Question from customer:
I want to use this remote kit to operate 4 ea.-12 volt flood lights on my RV (recreational vehicle) from inside my automobile if backing up at nighttime. I would keep one remote in my truck and one in the RV. Will this be a problem that the remote inside my truck will be at a distance of about 50 feet from the receivers inside the RV?
FLEETWOOD RV 2010 QUEST
Answer:
We recommend you 4 models of high power dc remote switch with direct power output (S1PX-DC12) and 2 long range transmitters (CB-4). Direct power output; controlling lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. When it pairs with the long range transmitter, the working distance will reach 500m (1600ft) in the open field. There is no need to worry about the distance. The most important point is that encoding of receivers is same as the code of transmitters. So they can work together.
remote control

Wiring:
The wiring is very simple. According to the wiring diagram, each light should be connected to corresponding receiver and place to appropriate position. Each receiver is supplied 12V power supply.
circuit

Usage:
There are 3 operational modes. Toggle, momentary and latched modes.
Setting control mode Toggle: Only connect Jumper-2.
Press big button: Turn on the relay.
Press big button again: Turn off the relay.
Setting control mode Momentary: Only connect Jumper-1.
Press and hold big button: Turn on the relay.
Release big button: Turn off the relay.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay.
Press small button: Turn off the relay.
You can choose latched mode since you have two transmitters. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time. To be more specific, when you control the light by latched mode, you should prepare at least two buttons remote. Press button A, the light is on; press button B, the light is off.
Button A&B of first transmitter can control the first light. Button C&D of the first transmitter can control the second light.
Button A&B of second transmitter can control the third light. Button C&D of the second transmitter can control the fourth light.

2013/08/26

A Transmitter Remote Control 2 Sirens—2000M

Question from Customer:
Hello, I would like some help to decide on what system to choose. We have a siren in a building 750m away that we would like to trigger, it is 240v. I would also like to use the same remote to activate a 12v siren 1.2km away. Is it possible for one remote to trigger two different sirens?
Answer:
We recommend you two different receivers, one is long range ac power direct output receiver (S1X-AC220-ANT2), and other is long range dc power direct output receiver (S1X-DC12-ANT2). AC receiver is used to connect to 240V siren. DC receiver is used to connect to 12V siren. You can only use 2-Button transmitter (CB-2) to control all of them. With the extended external antenna, both receivers’ working distances reach 2000m (6000ft).
remote control kit
Usage:
There are three working modes in each receiver.
1) Setting control mode Toggle: Only connect Jumper-2.
Press button 1: Turn on the relay.
Press button 1 again: Turn off the relay.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold button 1: Turn on the relay.
Release button 1: Turn off the relay.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press button 1: Turn on the relay.
Press button 2: Turn off the relay.
In your case, you can set ‘Toggle Mode’. Press the button of remote, turn on the device; press the button again, turn off the device. Toggle mode is motivated by single relay, which means you can work this mode with single button remote. So one 2-Button transmitter is enough for you to control two sirens. Press big button, turn on the 240V siren; press again, turn off the 240V siren. Press small button, switch on the 12V siren; press again, switch off the 12V siren.
Wiring:
240V siren is connected to AC receiver’s OUTPUT terminal. And supply 240V power supply. 12V siren is supposed to connect to DC receiver’s A&B terminal. And supply 12V power supply.
circuit

2013/08/22

Lamps are Controlled by Time Delay Receiver and Motion Detectors

We will try to make 2 motion detector led lamps with infrared motion detectors (W-01) and 2 channel rf receiver with time delay function (S2DA-DC12). The working distance of motion detector is 100m (open field). This delay time is adjustable and user-selectable. Delay time can be adjusted as you like within 0 second~99 hours.

 Operation Video:

2013/08/20

How to Remote Control Light Stations

A beacon is a light or fire on the hill or tower which acts as a signal or a warning to help guide navigator to their destination with safety.We also can say "Light Station" One customer said, “I’m looking for a system which can remotely control (200m max) ignition of a light station in 24 V dc”.
Leuchtturm in Podersdorf / Neusiedler See
We recommend him the model of single channel 24V power output RF remote (S1X-DC24-ANT2 +1CB-2). Single channel is for one device. 24V direct power output can supply power directly to the device which is controlled. User can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. The receiver, which mounts long range magnetic antenna, pairs with long distance transmitter to reach to 2000m in the open field.
remote control
There are 3 control modes. They are Toggle, momentary and latched.
Setting control mode Toggle: Only connect Jumper-2.
1) Press big button: Turn on the relay.
Press big button again: Turn off the relay.
2) Setting control mode Momentary: Only connect Jumper-1.
Press and hold big button: Turn on the relay.
Release big button: Turn off the relay.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Press big button: Turn on the relay.
Press small button: Turn off the relay.
As regards controlling beacon, we suggest the latched mode. Press big button to turn on beacon light, press small button to turn off the light.
For the wiring, it is so simple. The following picture shows. Lamp is connected to terminals A&B on the receiver. The receiver should be supplied 12V power. There is no need to supply power to lamp because lamp can get power from the receiver.
circuit

2013/08/16

Waterproof Remote Control for 2 LED Lamps

A brand new 2 channel 12V toggle remote control kit(S2RX-DC12 & C-2) is promoting now. The receiver is installed in a black waterproof case. Six colors‘ wires are connected inside terminals of the receiver. Wires are bound together and stuffed in black connection wire.The connection wire outside of the case is 20 cm. Wireless control 12V electronics including lights, LEDs, relays, dc motors and other low current devices.You can control receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. This video aims to show you how to control 2 led lamps.
Wires:
Red    =  Input +12V
Black  =  Input Ground (-)
Yellow =  Output 1 +12V
Brown  =  Output 1 Ground (-)
Blue   =  Output 2 +12V
Green  =  Output 2 Ground (-)
Operation Video:

2013/08/14

2 Channel DC Remote Controller with Manual Button and Limit Switch Function


With high power of 30A. Control DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V /24V.
You can rotate the motor in positive or reversal direction with the transmitter (remote control) from any place within a reliable distance; the wireless signal can pass through walls, floors and doors.

The remarkable characteristic of this controller is that its manual switch and limit switch, which meet your different requirements.

2013/08/12

2CH RF DC Remote Control Kit Controls AC Motor

This 2CH RF DC remote control kit is activated by DC power supply, which operates in toggle, momentary, latched and toggle +momentary modes (just set according to your requirement).It is very favorable for lights or other DC/AC electric devices which are hard to reach or far away from switch. This 2 channel remote control kit can help you complete two operations at the same time. It is widely used for lights, gates, garage doors, motors and so on.
We will try to show you how to control positive and reversal rotation of an AC motor with this remote module.

2013/08/07

1 CH Latched Remote Controller Controls LED Lamp

It is the 12 V one channel latched mode remote control. It is also activated by 12V power supply. Paired with long distance transmitter CB-2, its working distance can be 1000m (3000ft). There is no need to go up and down the mast to turn device on and off. Using a remote controller to control device, it is very convenient to you. As regards the latched mode, it is motivated by relay group. For relay group, only one relay will be on at a time. So the big button of this transmitter only turns on the
device when you press. And the small button only turns off the device.
We made a demonstration to show how to use this remote controller.

2013/08/02

One Transimtter to Many Receivers— Control 4 Lamps

The receiver is designed for one-transmitter-many-receivers system. There are two channels for each receiver. You can use 2 receivers with transmitter CV-4 or CB-4. You also can choose external antennas for them. With the extended external antennas, the transmitting distance will reach about 2000m in the open air. This kit is also a multi-mode remote control which includes four working modes, toggle, momentary, latched and momentary+toggle.